CEV Headlight Assembly. Typically came on Garelli mopeds. Would look great on any sort of future bike.

People love this Kit because it takes so much abuse, and still hangs tough.

Cheap thrills for you honda hobbit fans. 7 ports of fun. Big transfers, decent sized ports. Should be a ripper for sure. Transfers look to match the case, but open them up and open up the cases for secret hidden power.

Also, for perfect port timing, pick up this spacer kit.

Crazy cutaways on the piston reduce the weight, and super thin rings reduce friction on the piston wall.

For PA50, PA502, Express, and Camino.

Includes everything you see here:

Check out how this kit is being used on Garage. The worlds largest Moped Tuning Database. Here are some Honda builds featuring the Alu-Kit.

Performance Reed for Kitted Honda Hobbitt, Camino, PA50, PA50 II mopeds. Direct replacement, that gives you quite a punch. This reed is a Dual Stage reed that is designed to work with either modified cylinder, or bigger displacement kits.

Since it has two reeds, it is tuned for both torquey low-end, and great throttle response through the top.

Reeds:

Outer Top Reed = 0.6mm
Inner Split Reed = 0.3mm

Made out of Fiberglass.

Also works on a bunch of other non-moped 50cc bikes: Beta Tempo 50, Piaggio, Yamaha Axis, and Yamaha Jog 50.

These 6mm engine studs are for almost all cylinders and kits, and can be used for exhaust and intake studs.

Replacement gas cap for Puch and Tomos mopeds. Basically most step through bikes.

Keeps gas in and rain out. Totally worth it.

Replacement petcock for a pile of Bikes. General and Lazer Moped, Honda Express, NA50, NC50, MB5 and Yamaha QT50.

40mm x 1.5mm Piston Ring Set

Super Skinny tire if you are looking to break a spead record. Rated for 112mph!!

If you run this tire you have to run narrow inner tubes like

these

Now that you are running that CDI setup, and your spark is great, lets work on your lights!

4 x 6mm Studs. 100mm long. Works on the Honda PA50, Express, Hobbit, ect.

Mikuni performance in a slightly smaller size. The little brother to the Mikuni 24 Flatslide that is found on all serious race bikes.

Use the same jets as the TM series carb. Main jets available here. Comes with an installed #180 main jet.

This is a flange mounted carburetor. Uses a 32mm filter, same as a Dellorto PHBG.

The PHBG is a really great carburetor for the more advanced tuner. It helps you squeeze extra horsepower out of that expensive speed kit you just installed. This is a clone of the Dellorto PHBG that everyone loves.


The Race version gives you a touch more ease of access with a screw on Carb top, so you can change throttle slides, and adust your needle settings without removing your carb from your Ped. It also has an easy access bolt on the bottom of the float bowl for easily changing your main jet.

Oh, and its powdercoated black. How cool is that?

A little lesson on PHBG carbs. The first letter after the numbers: A means clamp on type mounting, B means rubber mounting, other letters were produced for specific applications and follow no rules The second letter is S for left, D for right as it refers to the side on the carb. where the mixture and throttle stop screws are.

main jet = 72
idle jet = 48
starter jet = 60
slide = 30
needle = W16
2 Stroke Atomizer!

For tuning tips, check out Garage. The worlds largest moped tuning database. Here are the list of the top builds in garage using this jet. Use Garage as a guide to what jet you need.

Some Dellorto 19mm Race Builds and the Jets they are using. 19mm PHBG Builds

This measuring cup is great, it has lines on the side indicating a 2% mix for 1, 1/2, or 1/4 gallons.

This is the most common nut found on your moped. It is called 6mm, or M6 in Metric speak. If you have a 10mm wrench or socket, and it fits the nut you need, this is it. This is the locking version of the common 6mm nut.

Used on exhaust studs, head bolts, and everywhere else.

Quantity discounts after 5. Keep adding them to your cart and watch the prices fall.

This headlight is a great replacement for the Tomos rectangular headlight. It also would look good just about anywhere you want a rectangular headlight. 

12v 35w.

Your basic New Old Stock 20 tooth freewheel. Will work on any moped that needs a freewheel.

The classic superman tail light assembly. OEM and NOS. The sample we took a photo with had no screws in it, it is possible they come with screws, but assume that they don't. If you get lens screws it will be a bonus!

This style light was found on tons of US bound mopeds. Puch Maxi, Peugeot 103, Motobecane, Honda, and many more. This light comes in a Peugeot bag.

Nothing finishes off a build or cleans up a bike like a new bezel for your headlight. Ditch that rusty, dinged up headlight bezel and get yourself one of these brand new chrome CEV headlight bezels and start turning heads.

Fits all CEV bullet and standard headlight buckets, as found on Puch, Peugeot, Italian bikes, and many more.

Finally a brand new headlight you will not blow out. This is a brand new ready to go 4.5in headlight.

Classic look with modern guts. This headlight runs a 12v H3 bulb commonly found in car headlights and offroad lights, much brighter than your usual moped light and also more reliable and easy to find. Cheap bulbs too! Great for hi-rpm CDI setups, and or mopeds with kits. Stock bikes with 12v systems can run these fine as well.

You probably don't need a voltage regulator, but why risk it? This bucket will go on pretty much anything you want to put it on.

This setup comes with a 12v55w bulb but most of the H3 bulbs you'll find at auto supply stores etc. are 12v55w. Have a crazy power lighting coil? 12v100w H3 bulbs are available too!

This throttle cable works on pretty much any moped.

If your original throttle cable had two ends, then make sure you get a throttle knarp.

47 inches long