People love this Kit because it takes so much abuse, and still hangs tough.

Minarelli V1 Polini, both Italian, and both fast. This kit is high quality. Dial it in, and don't worry about a thing. Not only do you get a really good speed boost, but these kits are very reliable. Sometimes referred to as the 80cc Minarelli Polini Kit.

These work with all Minarelli V1 based Mopeds. Cimatti, Testi, Fantic Motor, Yankee Peddler, Concord, and many more.

Like any performance upgrade, this kit will work better with its paired performance upgrades, like a matching carburetor and expansion chamber pipe. You will also want to modify the transfer ports in the engine cases in order to extract full performance from this item, but it will work at a reduced output as a bolt on addition.

As always on orders over $150, Free shippingin the USA.

Lots of folks are using these kits on Garage. The worlds largest moped tuning database. Here are the list of the top builds in Garage using the Minarelli V1 Polini.

This is a very high quality 16in tire. Fits many many Italian mopeds, and would be great for Tomos as well.

Made by DMP. Features 6 transfer ports. 2 Boost ports. Includes everything you see.


Joey Says: \"The best quality kit for $100. With porting can easily do 60mph\"

This kit is pretty popular on Garage, the worlds largest Moped tuning Database. Check out these builds using the DMP Puch Kit.

The K-Star kit is known around the world, and known by many names. Here it is: no gimmicks, no nicknames, just a great kit in its naked form.

Puch K-Star kit is great for the Puch Maxi, Magnum, Free Spirit, Pinto, and any other vintage Puch moped from roughly 1975 to 1985.

Small cost, with big performance, this kit is great for beginners and for the expert tuner. You can leave it mostly alone, clean up the ports, or port it like a Metrakit.

Sorry, no gaskets with this one.

Lots of folks are running this kit on Garage, the worlds largest Moped sharing website. Check out these K-Star builds here.

Works on any wet clutch that has a two hole pull. Puch, Minarelli, Morini, and Suzuki.

Perfect throttle for custom mopeds.

Puch 70cc Gasket Set. Perfect for all 45mm Puch kits.

Fits all Tomos mopeds.

It's a spring!

This Puch throttle cable fits mopeds with original style controls and Bing carbs. It is double ended and replaces the stock puch throttle cable. Works on most Maxi, Pinto, Newport and Freespirit mopeds. Check your old cable for comparison when buying.

This is a clone of the popular 15mm Puch Bing carburetor. It uses all the same parts as the real Bing, but is still a clone. Quality on this is about 90% that of an actual Bing. Folks seem to like it.

Perfect brake shoes for perfect stopping. Sometimes brakes get worn down enough than no amount of sanding can bring them back. These are for your Spoke, and 5 Star Puch wheels. Fits Motobecane, Sachs, Batavus, and Peugeot spoke rims as well. Basically all Lelue spoke rims use these.

Little Tip:

If your easy-adjust at the controls are all the way out, chances are your shoes are too far worn down, and should be replaced.

These 6mm engine studs are for almost all cylinders and kits, and can be used for exhaust and intake studs.

This puller is for all CEV brand magnetos, found on most italian moped models.

minarelli, garelli, tomos a3

CEV no. 6436 magnetos

Later MBK 51 Mobys with electronic ignition (CDI)

These 280mm coil-over shocks add 50 lbs. to your rated carry capacity, and come with an adjustable pre-load setting.

Mount holes are 10mm

Perfect fit for Minarelli, Tomos, Honda and other mopeds.

Replacement gas cap for Puch and Tomos mopeds. Basically most step through bikes.

Keeps gas in and rain out. Totally worth it.